Weldable EPDM Waterproofing - Weldable EPDM Waterproofing

Products

Home -Products

Weldable EPDM Waterproofing

(Gabrelia-B Standard ）

It has the best performance among polymer waterproof materials. It also has a special performance that it will not separate and crack in regular building movement. EPDM has excellent performance on weather resistance, dimensional stability and durability which brings it a good performance on high and low temperatures, UV and corrosion resistance. Moreover, TOP BEST - EPDM Waterproofing Membrane has other properties like high tensile strength and breaking elongation, movement adaptation, ease of installation, strong alliances, non-pollution, strong puncture resistance and long service life of 50 years. Its Shelf life is 12 months if put in a cool and dry place with original package.

- Excellent weather-ability, durability and size stability

- Good adaptability to high and low temperature, UV resistant and anti-corrosion

- High tensile strength and good elongation, accommodating to structure movement

- Easy installation, solid joint, and no environmental pollution

- Good rooting penetration resistance

- Service life up to 50 years

- Excellent physical and mechanical performance

- High tearing resistance

- Good deformation adaptability

- High puncture resistance

- High aging resistance

- - UV resistance

Specifications
1	Thickness		0.8/1.0/1.2/1.5/2.0mm
2	Length		20m or customized
3	Width		1.0m/1.2m/2.0m/3m/4m or others 8m widest
4	Whether vulcanized		Unvulcanized
5	Certification		ISO9001, ISO14001
6	Colour		Customized
7	Packaging Details		Tape Plastic Bag
8	Tensile fracture strength/Mpa	（60℃）	≥0.8
		（23℃）	≥4.0
9	Elongation at break	（23℃）	≥400%
		（- 20℃）	≥200%
10	Thermal Stability (mm)	Extend (mm）	≤2
		Shrink(mm）	≤4
11	Peel strength（Kn/m）		≥18
12	Impermeability （30Min) 0.3Mpa		No leaking
Bonding Peel Strength (Sheet and Sheet)	N/mm (Standard test conditions)		≥1.5
	Soaking retention rate (23℃×168h)		≥70%
14	Low Temperature Bend Temperature /℃		No cracks at -30℃
15	Hot Air Aging 80℃*168h	Retention of Tensile （%）fracture strength	≥90%
		Retention of Elongation at break（%）	≥70%
16	Ozone aging 40℃*168h	Retention of Elongation at break（%）	Elongation 40%, 500pphm, no crack
17	Artificial weathering	Retention of Tensile fracture strength（%）	≥80%
		Retention of Elongation at break（%）	≥70%
18	Alkali tolerance Saturated sodium hydroxide solution, room temperature*168 hours	Retention of Tensile fracture strength（%）	≥80%
		Retention of Elongation at break（%）	≥90%

Updating...

- the substratum should be smooth, dry, clean, which cannot have loosing and peeling phenomena.

- Before application, clean up the basic level and eradicate the impurities.

- Spread out the membrane on the substratum to loose sheet's stress. Use adhesive-glue to paint the substratum and the surface of membrane. When the adhesive is not sticky to hands, pave and press smoothly.

- When pave the second volume of membrane, extrude 100mm of the edge of overlap of the first roll and do not paint with the adhesive. Pave the membrane on the substratum according to step so as to finish the whole pavement. When paving, do not tighten the waterproof membrane violently.

- After that, use the special solvent to scrub the overlap joint. When it becomes fully dry, use the sheet glue to paint the both sides of the joint. Paint it again when it gets completely dry. Till the adhesive is not sticky to hands, press it smoothly and solidly.

- Pay attention to fire prevention during application. Basement construction site shall be equipped with ventilation facilities

· Do not operate when rain, snow, strong wind.

· Train before operation.

- Different types or specifications of products should be separated, not mixed

- Keep it dry and ventilated, protected from the sun or rain.

- Storage temperature should never be higher than 45 °C. Pile up the membranes flatwise whose stockpile height never exceeds five layers. One layer is guaranteed if it is placed vertically.

- Prevent it from inclination or In the process of transportation, it should be lying in case of inclination or lateral pressure. If necessary, cover it with felt-cloth.

- Storage time is at least one year from manufacture date on if the product is under normal operation of storage.

24h national service hotline (WhatsApp)

Useful Links

Products

Contact

+86 13062884852 (China) +7 904760-12-40 (Russia)
ceo@gabrielia.com
Universiade Village 6, Kazan city, Republic of Tatarstan, Russian Federation (Russia Office）
Jinxiu East Road, Kengzi Street, Pingshan District, Shenzhen City (Headquarters)
23 đường 320 Bông Sao Phường 05 Quận 08 Tp.hcm (Việt Nam)