Weldable EPDM Waterproofing - Weldable EPDM Waterproofing

Products

Home -Products

Weldable EPDM Waterproofing

(Gabrelia-B Self-Adhensive ）

EPDM self-adhesive waterproofing membrane is a first-class extrusion all over the world, self-adhesive layer with high strength of the pressure sensitivity and reactivity, with the cast-in-place concrete base to form a suction cup effect and inorganic reaction in concrete to form a chemical bond, To achieve with the concrete "skin type" full sticky effect. The material is environmentally friendly, non-toxic, tasteless, flexible, durable and physical properties are better than the traditional asphalt self-adhesive coil, to meet the modern high-grade Building a century of life design requirements, is the best waterproofing waterproof construction materials and also the preferred waterproof building materials at home and abroad.

- Excellent physical and mechanical performance

- High tearing resistance

- Good deformation adaptability

- High puncture resistance

- High aging resistance

- UV resistance

- Super strong cohesive force, the web self-adhesive layer directly generated by polymerization, cannot be stripped away, sealed waterproof not channeling water.

- Domestic and foreign polymer self-adhesive waterproofing membrane: The first material directly on the surface of the formation of self-adhesive layer bonding technology, can be combined with the concrete bonded together to achieve a permanent waterproof effect.Construction Methods

Specifications
1	Thickness		1mm 1.5mm 2mm
2	Length		1m-100m
3	Width		1m-4m
4	Whether vulcanized		Unvulcanized
5	Certification		ISO9001, ISO14001
6	Colour		Customized可定制
7	Packaging Details		Tape Plastic Bag
8	Tensile fracture strength/Mpa	（23℃）	≥7.5
9	Elongation at break/%	（23℃）	≥450
10	Thermal extension	Extend(mm）	≤2mm
		Shrink(mm）	≤4mm
11	Peel strength（Kn/m）		≥25
12	Impermeability （30Min) 0.3Mpa		No leakage
13	Low Temperature Bend Temperature/℃		Material Layer:No cracks at -40℃ Adhesive Layer:No cracks at -25℃
	Stickiness/Min		≥20
14 Peel strength	Standard Environment Condition	Sheet to sheet	≥0.8
		Sheet to aluminum plate	≥1.0
		Sheet to Cement Mortar Board	≥1.0
	Heat & Aging Condition （80℃*86h)	Sheet to sheet	≥1.0
		Sheet to aluminum plate	≥1.2
		Sheet to Cement Mortar Board	≥1.2
15	Hot Air Aging 80℃*168h	Retention of Tensile fracture strength（%）	≥90
		Retention of Elongation at break（%）	≥70
16	Ozone aging 40℃*168h	Retention of Tensile fracture strength（%）	No Crack
		Retention of Elongation at break	No Crack
16	Artificial weathering	Retention of Tensile fracture strength（%）	≥80
		Retention of Elongation at break（%）	≥70
17	Alkali tolerance Saturated sodium hydroxide solution, room temperature*168 hours	Retention of Tensile fracture strength（%）	≥80
		Retention of Elongation at break（%）	≥90

- Roofs, Basement, Toilets

- Industrial and civil building waterproofing

- Geosynthetic liner for swimming pool, channels, irrigation system

- Especially suitable for projects with high requirements in durability, anti-corrosion and deformations.

- The substratum should be smooth, dry, clean, which can not have loosing and peeling phenomena.

- Before application, clean up the basic level and eradicate the impurities.

- Spread out the membrane on the substratum to loose sheet's stress. Use adhesive-glue to paint the substratum and the surface of membrane. When the adhesive is not sticky to hands, pave and press smoothly.

- When pave the second volume of membrane, extrude 100mm of the edge of overlap of the first roll and do not paint with the adhesive. Pave the membrane on the substratum according to step so as to finish the whole pavement. When paving, do not tighten the waterproof membrane violently.

- After that, use the special solvent to scrub the overlap joint. When it becomes fully dry, use the sheet glue to paint the both sides of the joint. Paint it again when it gets completely dry. Till the adhesive is not sticky to hands, press it smoothly and solidly.

- Pay attention to fire prevention during application. Basement construction site shall be equipped with ventilation facilities

·Do not operate when rain, snow, strong wind.

·Train before operation.

- Different types or specifications of products should be separated, not mixed

- .Keep it dry and ventilated, protected from the sun or rain.

- Storage temperature should never be higher than 45 °C. Pile up the membranes flatwise whose stockpile height never exceeds five layers. One layer is guaranteed if it is placed vertically.

- Prevent it from inclination or In the process of transportation, it should be lying in case of inclination or lateral pressure. If necessary, cover it with felt-cloth.

- Storage time is at least one year from manufacture date on if the product is under normal operation of storage.

24h national service hotline (WhatsApp)

Useful Links

Products

Contact

+86 13062884852 (China) +7 904760-12-40 (Russia)
ceo@gabrielia.com
Universiade Village 6, Kazan city, Republic of Tatarstan, Russian Federation (Russia Office）
Jinxiu East Road, Kengzi Street, Pingshan District, Shenzhen City (Headquarters)
23 đường 320 Bông Sao Phường 05 Quận 08 Tp.hcm (Việt Nam)